Products search search close

IO108

Fast 16-bit Analog Output Module

The IO108 module is a dedicated fast, 16-bit analog output module with Simulink® driver blocks.

Each of the 8 output channels has a dedicated D/A converter with an update time of 2.2 μs.

The output coupling of the module can be either differential or singleended (build option), and the voltage ranges can be ±10 V, ±5 V, ±2.5 V or ±1.25 V, or as a build option ±20 V, ±10 V or ±5 V. Several of these modules can be interconnected by trigger lines to synchronously update analog output channels across the different modules.

This I/O module is ideal for closed-loop controls and hardware-in-theloop (HIL) simulations using MATLAB® and Simulink.

Key Features

  • Up to 8 balanced differential 3-wire, or 2-wire single-ended outputs (build option)
  • Dedicated D/A converter per channel (simultaneous), 16-bit resolution
  • 2.2 μs update time per channel with DMA (450 kSPS), and 5 μs settling time per channel
  • Software selectable ±10 V, ±5 V, ±2.5 V, 1.25 V, or ±20 V, ±10 V, ±5 V (build option) output voltage range
  • Auto-calibration of entire analog output section
  • Simulink Real-Time™ analog output driver blocks
Physical  
Form factor PMC
Power requirements 5.5W typical, 7.5W maximum
Bus PCI D32, 33/66 MHz, specification 2.3
EMI EMI shield on component side
Connector 68-pin SCSI3
Cable connectors: Tyco Electronics
Board connector: Tyco Electronics part no. 5749069-7
Environmental  
Operating temperature 0 to 70 °C (extended temperature option: -40 °C to +85 °C)
Relative humidity 0 to 95 %, non-condensing
Analog Outputs  
Number of outputs 8 x balanced differential 3-wire, or 2-wire single-ended outputs (build option).
Max data rate 450 kSPS with DMA
Settling time 5µs to 0.1% with no filter
Voltage ranges Software selectable ±10V, ±5V, ±2.5V or ±1.25V or
±20V, ±10V, ±5V (build option)
Output protection Withstands sustained short-circuiting to ground
Output resistance 1.0 Ohm maximum
Output resistance Withstands sustained short-circuiting to ground
Bandwidth 300 kHz, typical -3 dB
Reliability  
Mean time between failures (MTBF)* 217,150 hours
MTBF (Mean Time Between Failure) - MTBF values shown are based on calculation according to MIL-HDBK-217F and MIL-HDBK-217F Notice 2; Environment: GB 20°C. The MTBF calculation is based on component FIT rates provided by the component suppliers. If FIT rates are not available, MIL-HDBK-217F and MIL-HDBK-217F Notice 2 formulas are used for the FIT rate calculation.
Item ID Product Name Components
2A108X* IO108-DF
  • 1 x IO108 with 8 differential analog outputs
  • ±10V, ±5V, ±2.5V or ±1.25V output voltage ranges
  • 1 x 68-Pin SCSI3 to 68-pin MDR cable, 1.82m (6ft) long
  • 1 x 68-Pin Female MDR Terminal board
  • Driver block library for Simulink Real-Time™
  • Comprehensive documentation and Simulink example models
  • Installation into the real-time target machine
2C108X* IO108-DF-HV
  • 1 x IO108 with 8 differential analog outputs
  • ±20V, ±10V, or ±5V output voltage ranges
  • 1 x 68-Pin SCSI3 to 68-pin MDR cable, 1.82m (6ft) long
  • 1 x 68-Pin Female MDR Terminal board
  • Driver block library for Simulink Real-Time™
  • Comprehensive documentation and Simulink example models
  • Installation into the real-time target machine
2B108X* IO108-SE
  • 1 x IO108 with 8 single-ended analog outputs
  • ±10V, ±5V, ±2.5V or ±1.25V output voltage ranges
  • 1 x 68-Pin SCSI3 to 68-pin MDR cable, 1.82m (6ft) long
  • 1 x 68-Pin Female MDR Terminal board
  • Driver block library for Simulink Real-Time™
  • Comprehensive documentation and Simulink example models
  • Installation into the real-time target machine
201089X* IO108-ExtTemp
  • Increases temperature range of IO108 from 0 to +70ºC
    to -40ºC to +85ºC. Available for all IO108 versions

Key to X in Item ID
Please replace the X with the code number of the specific target machine into which this I/O module shall be installed:

  • 5 = Mobile real-time target machine
  • 6 = Performance real-time target machine
  • 8 = Baseline real-time target machine

Pricing information
We don't publish pricing information on our website. Upon request by e-mail or phone we can provide a complete price list covering our entire product portfolio in various currencies. We recommend that you get in touch with us to discuss your specific needs. We can then quickly provide you with a tailored quotation including technical and pricing information.

 

Included in delivery

Common Applications

Supported target machines

Resources

Follow Speedgoat LinkedIn